[LinuxBIOS] Kernel lock-ups??

joe at smittys.pointclark.net joe at smittys.pointclark.net
Mon Oct 15 20:58:27 CEST 2007


Quoting Jordan Crouse <jordan.crouse at amd.com>:

>> I have HAVE_PIRQ_TABLE=1 and irq_tables.c.
>> What is the utility for the MP table?
>>
>> Anyways I tried these kernel options acpi=off irqpoll lpj=720896
>> and it gets a little further. Now it locks-up on this line:
>>
>> Checking 'hlt' instruction...
>>
>> Any ideas?
>
> Interrupts are very obviously broken.  In this case, its waiting for an
> interrupt to verify that the 'hlt' instruction works.  You can work around
> this as well, if you want, but its really going to be in your best interest
> to figure out whats wrong in the BIOS.
>
> Jordan
>
I agree Jordan it needs to be fixed in LB. I don't really know where  
to start. Can someone point me in the right direction? Everything  
looks ok in my bootlog.
Here is the output pertaining to the irq_routing_table.

Copying IRQ routing tables to 0xf0000...done.
Verifing copy of IRQ routing tables at 0xf0000...done
Checking IRQ routing table consistency...
check_pirq_routing_table() - irq_routing_table located at: 0x000f0000
done.
Moving GDT to 0x500...ok
Adjust low_table_end from 0x00000530 to 0x00001000
Adjust rom_table_end from 0x000f0400 to 0x00100000
Wrote linuxbios table at: 00000530 - 000006ec  checksum 622a

Heck, I just attached my whole bootlog. Please take a look and see if  
you can see anything wrong. I would really appreciate it.

Thanks - Joe
-------------- next part --------------
LinuxBIOS-2.0.0.0RM4100 Mon Oct 15 07:42:50 EDT 2007 starting...
Setting initial registers....
Initial registers have been set.
No DIMM found in slot 00
DRB 0x60 has been set to 0x00
DRB1 0x61 has been set to 0x00
Found DIMM in slot 01
DIMM is 0x0080 on side 1
DIMM is 0x0000 on side 2
DRB2 0x62 has been set to 0x04
DRB3 0x63 has been set to 0x04
No DIMM found in slot 00, setting DRA to 0xFF
DRA 0x70 has been set to 0xff
Found DIMM in slot 01, setting DRA...
DRA 0x71 has been set to 0xf1
RAM Enable 1: Apply NOP
    Sending RAM command 0x00000010 to 0x00000000
RAM Enable 2: Precharge all
    Sending RAM command 0x00000020 to 0x00000000
RAM Enable 3: CBR
    Sending RAM command 0x00000060 to 0x00000000
    Sending RAM command 0x00000060 to 0x00000000
    Sending RAM command 0x00000060 to 0x00000000
    Sending RAM command 0x00000060 to 0x00000000
    Sending RAM command 0x00000060 to 0x00000000
    Sending RAM command 0x00000060 to 0x00000000
    Sending RAM command 0x00000060 to 0x00000000
    Sending RAM command 0x00000060 to 0x00000000
RAM Enable 4: Mode register set
    Sending RAM command 0x00000030 to 0x000001d0
RAM Enable 5: Normal operation
    Sending RAM command 0x20000270 to 0x00000000
Northbridge following SDRAM init:
PCI: 00:00.00
00: 86 80 75 35 06 00 10 00 04 00 00 06 00 00 00 00
10: 08 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 40 00 00 00 00 00 00 00 00 00 00 00
40: 09 00 05 01 00 00 00 00 00 00 00 00 02 28 00 0e
50: 72 a0 00 00 00 00 00 00 00 30 33 33 33 33 33 33
60: 00 00 04 04 04 04 00 00 00 00 00 00 00 00 00 00
70: ff f1 ff ff 00 00 00 00 10 00 00 00 70 02 00 20
80: 00 00 00 00 00 00 00 00 00 d0 20 40 00 00 00 00
90: 02 38 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 02 00 20 00 17 02 00 1f 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 54 0e 41 a2 99 01 00 c0 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 1b 49 9b fc
f0: 11 11 01 00 00 00 0b 05 34 d6 34 cf 22 cf 24 cf
Testing DRAM : 07700000-07800000
DRAM fill: 07700000-07800000
07700000 
07710000 
07720000 
07730000 
07740000 
07750000 
07760000 
07770000 
07780000 
07790000 
077a0000 
077b0000 
077c0000 
077d0000 
077e0000 
077f0000 
07800000
DRAM filled
DRAM verify: 07700000-07800000
07700000 
07710000 
07720000 
07730000 
07740000 
07750000 
07760000 
07770000 
07780000 
07790000 
077a0000 
077b0000 
077c0000 
077d0000 
077e0000 
077f0000 
07800000
DRAM range verified.
Done.
Copying LinuxBIOS to RAM.
Jumping to LinuxBIOS.
LinuxBIOS-2.0.0.0RM4100 Mon Oct 15 07:42:50 EDT 2007 booting...
end 727a6499, start 0
32-bit delta 1572
calibrate_tsc 32-bit result is 1572
clocks_per_usec: 1572
Enumerating buses...
scan_static_bus for Root Device
Finding PCI configuration type.
PCI: Using configuration type 1
PCI_DOMAIN: 0000 enabled
PCI_DOMAIN: 0000 scanning...
PCI: pci_scan_bus for bus 00
PCI: 00:00.0 [8086/3575] ops
PCI: 00:00.0 [8086/3575] enabled
PCI: devfn 0x8, bad id 0xffffffff
PCI: 00:02.0 [8086/3577] enabled
PCI: devfn 0x18, bad id 0xffffffff
PCI: devfn 0x20, bad id 0xffffffff
PCI: devfn 0x28, bad id 0xffffffff
PCI: devfn 0x30, bad id 0xffffffff
PCI: devfn 0x38, bad id 0xffffffff
PCI: devfn 0x40, bad id 0xffffffff
PCI: devfn 0x48, bad id 0xffffffff
PCI: devfn 0x50, bad id 0xffffffff
PCI: devfn 0x58, bad id 0xffffffff
PCI: devfn 0x60, bad id 0xffffffff
PCI: devfn 0x68, bad id 0xffffffff
PCI: devfn 0x70, bad id 0xffffffff
PCI: devfn 0x78, bad id 0xffffffff
PCI: devfn 0x80, bad id 0xffffffff
PCI: devfn 0x88, bad id 0xffffffff
PCI: devfn 0x90, bad id 0xffffffff
PCI: devfn 0x98, bad id 0xffffffff
PCI: devfn 0xa0, bad id 0xffffffff
PCI: devfn 0xa8, bad id 0xffffffff
PCI: devfn 0xb0, bad id 0xffffffff
PCI: devfn 0xb8, bad id 0xffffffff
PCI: devfn 0xc0, bad id 0xffffffff
PCI: devfn 0xc8, bad id 0xffffffff
PCI: devfn 0xd0, bad id 0xffffffff
PCI: devfn 0xd8, bad id 0xffffffff
PCI: devfn 0xe0, bad id 0xffffffff
PCI: 00:1d.0 [8086/24c2] ops
PCI: 00:1d.0 [8086/24c2] enabled
PCI: 00:1d.1 [8086/24c4] ops
PCI: 00:1d.1 [8086/24c4] enabled
PCI: 00:1d.2 [8086/24c7] ops
PCI: 00:1d.2 [8086/24c7] enabled
PCI: devfn 0xeb, bad id 0xffffffff
PCI: devfn 0xec, bad id 0xffffffff
PCI: devfn 0xed, bad id 0xffffffff
PCI: devfn 0xee, bad id 0xffffffff
PCI: 00:1d.7 [8086/24cd] ops
PCI: 00:1d.7 [8086/24cd] enabled
PCI: 00:1e.0 [8086/244e] bus ops
PCI: 00:1e.0 [8086/244e] enabled
PCI: 00:1f.0 [8086/24c0] bus ops
PCI: 00:1f.0 [8086/24c0] enabled
PCI: 00:1f.1 [8086/24cb] ops
PCI: 00:1f.1 [8086/24cb] enabled
PCI: devfn 0xfa, bad id 0xffffffff
PCI: 00:1f.3 [8086/24c3] enabled
PCI: devfn 0xfc, bad id 0xffffffff
PCI: 00:1f.5 [8086/24c5] ops
PCI: 00:1f.5 [8086/24c5] enabled
PCI: 00:1f.6 [8086/24c6] ops
PCI: 00:1f.6 [8086/24c6] enabled
PCI: devfn 0xff, bad id 0xffffffff
do_pci_scan_bridge for PCI: 00:1e.0
PCI: pci_scan_bus for bus 01
PCI: devfn 0x0, bad id 0xffffffff
PCI: devfn 0x8, bad id 0xffffffff
PCI: devfn 0x10, bad id 0xffffffff
PCI: devfn 0x18, bad id 0xffffffff
PCI: devfn 0x20, bad id 0xffffffff
PCI: devfn 0x28, bad id 0xffffffff
PCI: devfn 0x30, bad id 0xffffffff
PCI: devfn 0x38, bad id 0xffffffff
PCI: devfn 0x40, bad id 0xffffffff
PCI: devfn 0x48, bad id 0xffffffff
PCI: devfn 0x50, bad id 0xffffffff
PCI: devfn 0x58, bad id 0xffffffff
PCI: devfn 0x60, bad id 0xffffffff
PCI: devfn 0x68, bad id 0xffffffff
PCI: devfn 0x70, bad id 0xffffffff
PCI: devfn 0x78, bad id 0xffffffff
PCI: devfn 0x80, bad id 0xffffffff
PCI: devfn 0x88, bad id 0xffffffff
PCI: devfn 0x90, bad id 0xffffffff
PCI: devfn 0x98, bad id 0xffffffff
PCI: devfn 0xa0, bad id 0xffffffff
PCI: devfn 0xa8, bad id 0xffffffff
PCI: devfn 0xb0, bad id 0xffffffff
PCI: devfn 0xb8, bad id 0xffffffff
PCI: devfn 0xc0, bad id 0xffffffff
PCI: devfn 0xc8, bad id 0xffffffff
PCI: devfn 0xd0, bad id 0xffffffff
PCI: devfn 0xd8, bad id 0xffffffff
PCI: devfn 0xe0, bad id 0xffffffff
PCI: devfn 0xe8, bad id 0xffffffff
PCI: devfn 0xf0, bad id 0xffffffff
PCI: devfn 0xf8, bad id 0xffffffff
PCI: pci_scan_bus returning with max=001
do_pci_scan_bridge returns max 1
scan_static_bus for PCI: 00:1f.0
Found SMSC Super I/O (ID=0x60, rev=0x01)
PNP: 002e.0 disabled
PNP: 002e.3 disabled
PNP: 002e.4 enabled
PNP: 002e.5 disabled
PNP: 002e.7 enabled
PNP: 002e.9 disabled
PNP: 002e.a disabled
PNP: 002e.b disabled
scan_static_bus for PCI: 00:1f.0 done
PCI: pci_scan_bus returning with max=001
scan_static_bus for Root Device done
done
Allocating resources...
Reading resources...
Root Device compute_allocate_io: base: 00000400 size: 00000000 align: 0 gran: 0
Root Device read_resources bus 0 link: 0
PCI_DOMAIN: 0000 read_resources bus 0 link: 0
PCI: 00:00.0 register 10(00000008), read-only ignoring it
PCI: 00:1e.0 compute_allocate_io: base: 00000000 size: 00000000 align: 12 gran: 12
PCI: 00:1e.0 read_resources bus 1 link: 0
PCI: 00:1e.0 read_resources bus 1 link: 0 done
PCI: 00:1e.0 compute_allocate_io: base: 00000000 size: 00000000 align: 12 gran: 12 done
PCI: 00:1e.0 compute_allocate_io: base: 0000f000 size: 00000000 align: 12 gran: 12
PCI: 00:1e.0 read_resources bus 1 link: 0
PCI: 00:1e.0 read_resources bus 1 link: 0 done
PCI: 00:1e.0 compute_allocate_io: base: 0000f000 size: 00000000 align: 12 gran: 12 done
PCI: 00:1e.0 1c <- [0x000000f000 - 0x000000efff] bus 01 io
PCI: 00:1e.0 compute_allocate_prefmem: base: 00000000 size: 00000000 align: 20 gran: 20
PCI: 00:1e.0 read_resources bus 1 link: 0
PCI: 00:1e.0 read_resources bus 1 link: 0 done
PCI: 00:1e.0 compute_allocate_prefmem: base: 00000000 size: 00000000 align: 20 gran: 20 done
PCI: 00:1e.0 compute_allocate_prefmem: base: fff00000 size: 00000000 align: 20 gran: 20
PCI: 00:1e.0 read_resources bus 1 link: 0
PCI: 00:1e.0 read_resources bus 1 link: 0 done
PCI: 00:1e.0 compute_allocate_prefmem: base: fff00000 size: 00000000 align: 20 gran: 20 done
PCI: 00:1e.0 24 <- [0x00fff00000 - 0x00ffefffff] bus 01 prefmem
PCI: 00:1e.0 compute_allocate_mem: base: 00000000 size: 00000000 align: 20 gran: 20
PCI: 00:1e.0 read_resources bus 1 link: 0
PCI: 00:1e.0 read_resources bus 1 link: 0 done
PCI: 00:1e.0 compute_allocate_mem: base: 00000000 size: 00000000 align: 20 gran: 20 done
PCI: 00:1e.0 compute_allocate_mem: base: fff00000 size: 00000000 align: 20 gran: 20
PCI: 00:1e.0 read_resources bus 1 link: 0
PCI: 00:1e.0 read_resources bus 1 link: 0 done
PCI: 00:1e.0 compute_allocate_mem: base: fff00000 size: 00000000 align: 20 gran: 20 done
PCI: 00:1e.0 20 <- [0x00fff00000 - 0x00ffefffff] bus 01 mem
PCI: 00:1f.0 read_resources bus 0 link: 0
PCI: 00:1f.0 read_resources bus 0 link: 0 done
PCI_DOMAIN: 0000 read_resources bus 0 link: 0 done
Root Device read_resources bus 0 link: 0 done
PCI: 00:1f.5 10 *  [0x00000400 - 0x000004ff] io
PCI: 00:1f.6 10 *  [0x00000800 - 0x000008ff] io
PCI: 00:1f.6 14 *  [0x00000c00 - 0x00000c7f] io
PCI: 00:1f.5 14 *  [0x00000c80 - 0x00000cbf] io
PCI: 00:1d.0 20 *  [0x00000cc0 - 0x00000cdf] io
PCI: 00:1d.1 20 *  [0x00000ce0 - 0x00000cff] io
PCI: 00:1d.2 20 *  [0x00001000 - 0x0000101f] io
PCI: 00:1f.3 20 *  [0x00001020 - 0x0000103f] io
PCI: 00:1f.1 20 *  [0x00001040 - 0x0000104f] io
PCI: 00:1f.1 10 *  [0x00001050 - 0x00001057] io
PCI: 00:1f.1 18 *  [0x00001060 - 0x00001067] io
PCI: 00:1f.1 14 *  [0x00001070 - 0x00001073] io
PCI: 00:1f.1 1c *  [0x00001080 - 0x00001083] io
Root Device compute_allocate_io: base: 00001084 size: 00000c84 align: 8 gran: 0 done
Root Device compute_allocate_mem: base: 00000000 size: 00000000 align: 0 gran: 0
Root Device read_resources bus 0 link: 0
Root Device read_resources bus 0 link: 0 done
PCI: 00:02.0 10 *  [0x00000000 - 0x07ffffff] prefmem
PCI: 00:02.0 14 *  [0x08000000 - 0x0807ffff] mem
PCI: 00:1d.7 10 *  [0x08080000 - 0x080803ff] mem
PCI: 00:1f.1 24 *  [0x08081000 - 0x080813ff] mem
PCI: 00:1f.5 18 *  [0x08082000 - 0x080821ff] mem
PCI: 00:1f.5 1c *  [0x08083000 - 0x080830ff] mem
Root Device compute_allocate_mem: base: 08083100 size: 08083100 align: 27 gran: 0 done
Done reading resources.
Setting resources...
Root Device compute_allocate_io: base: 00001000 size: 00000c84 align: 8 gran: 0
Root Device read_resources bus 0 link: 0
Root Device read_resources bus 0 link: 0 done
PCI: 00:1f.5 10 *  [0x00001000 - 0x000010ff] io
PCI: 00:1f.6 10 *  [0x00001400 - 0x000014ff] io
PCI: 00:1f.6 14 *  [0x00001800 - 0x0000187f] io
PCI: 00:1f.5 14 *  [0x00001880 - 0x000018bf] io
PCI: 00:1d.0 20 *  [0x000018c0 - 0x000018df] io
PCI: 00:1d.1 20 *  [0x000018e0 - 0x000018ff] io
PCI: 00:1d.2 20 *  [0x00001c00 - 0x00001c1f] io
PCI: 00:1f.3 20 *  [0x00001c20 - 0x00001c3f] io
PCI: 00:1f.1 20 *  [0x00001c40 - 0x00001c4f] io
PCI: 00:1f.1 10 *  [0x00001c50 - 0x00001c57] io
PCI: 00:1f.1 18 *  [0x00001c60 - 0x00001c67] io
PCI: 00:1f.1 14 *  [0x00001c70 - 0x00001c73] io
PCI: 00:1f.1 1c *  [0x00001c80 - 0x00001c83] io
Root Device compute_allocate_io: base: 00001c84 size: 00000c84 align: 8 gran: 0 done
Root Device compute_allocate_mem: base: f0000000 size: 08083100 align: 27 gran: 0
Root Device read_resources bus 0 link: 0
Root Device read_resources bus 0 link: 0 done
PCI: 00:02.0 10 *  [0xf0000000 - 0xf7ffffff] prefmem
PCI: 00:02.0 14 *  [0xf8000000 - 0xf807ffff] mem
PCI: 00:1d.7 10 *  [0xf8080000 - 0xf80803ff] mem
PCI: 00:1f.1 24 *  [0xf8081000 - 0xf80813ff] mem
PCI: 00:1f.5 18 *  [0xf8082000 - 0xf80821ff] mem
PCI: 00:1f.5 1c *  [0xf8083000 - 0xf80830ff] mem
Root Device compute_allocate_mem: base: f8083100 size: 08083100 align: 27 gran: 0 done
Root Device assign_resources, bus 0 link: 0
Setting RAM size to 131072
PCI_DOMAIN: 0000 assign_resources, bus 0 link: 0
PCI: 00:02.0 10 <- [0x00f0000000 - 0x00f7ffffff] prefmem
PCI: 00:02.0 14 <- [0x00f8000000 - 0x00f807ffff] mem
PCI: 00:1d.0 20 <- [0x00000018c0 - 0x00000018df] io
PCI: 00:1d.1 20 <- [0x00000018e0 - 0x00000018ff] io
PCI: 00:1d.2 20 <- [0x0000001c00 - 0x0000001c1f] io
PCI: 00:1d.7 10 <- [0x00f8080000 - 0x00f80803ff] mem
PCI: 00:1f.0 assign_resources, bus 0 link: 0
PNP: 002e.4 60 <- [0x00000003f8 - 0x00000003ff] io
PNP: 002e.4 70 <- [0x0000000004 - 0x0000000004] irq
PNP: 002e.7 60 <- [0x0000000060 - 0x0000000060] io
PNP: 002e.7 62 <- [0x0000000064 - 0x0000000064] io
PNP: 002e.7 70 <- [0x0000000001 - 0x0000000001] irq
PNP: 002e.7 72 <- [0x000000000c - 0x000000000c] irq
PCI: 00:1f.0 assign_resources, bus 0 link: 0
PCI: 00:1f.1 10 <- [0x0000001c50 - 0x0000001c57] io
PCI: 00:1f.1 14 <- [0x0000001c70 - 0x0000001c73] io
PCI: 00:1f.1 18 <- [0x0000001c60 - 0x0000001c67] io
PCI: 00:1f.1 1c <- [0x0000001c80 - 0x0000001c83] io
PCI: 00:1f.1 20 <- [0x0000001c40 - 0x0000001c4f] io
PCI: 00:1f.1 24 <- [0x00f8081000 - 0x00f80813ff] mem
PCI: 00:1f.3 20 <- [0x0000001c20 - 0x0000001c3f] io
PCI: 00:1f.5 10 <- [0x0000001000 - 0x00000010ff] io
PCI: 00:1f.5 14 <- [0x0000001880 - 0x00000018bf] io
PCI: 00:1f.5 18 <- [0x00f8082000 - 0x00f80821ff] mem
PCI: 00:1f.5 1c <- [0x00f8083000 - 0x00f80830ff] mem
PCI: 00:1f.6 10 <- [0x0000001400 - 0x00000014ff] io
PCI: 00:1f.6 14 <- [0x0000001800 - 0x000000187f] io
PCI_DOMAIN: 0000 assign_resources, bus 0 link: 0
Root Device assign_resources, bus 0 link: 0
Done setting resources.
Done allocating resources.
Enabling resources...
PCI: 00:00.0 cmd <- 06
PCI: 00:02.0 subsystem <- 00/00
PCI: 00:02.0 cmd <- 02
PCI: 00:1d.0 cmd <- 01
PCI: 00:1d.1 cmd <- 01
PCI: 00:1d.2 cmd <- 01
PCI: 00:1d.7 subsystem <- 00/00
PCI: 00:1d.7 cmd <- 02
PCI: 00:1e.0 bridge ctrl <- 0003
PCI: 00:1e.0 cmd <- 01
PCI: 00:1f.0 cmd <- 0f
PCI: 00:1f.1 cmd <- 03
PCI: 00:1f.3 subsystem <- 00/00
PCI: 00:1f.3 cmd <- 01
PCI: 00:1f.5 cmd <- 03
PCI: 00:1f.6 cmd <- 01
done.
Initializing devices...
Root Device init
PCI: 00:00.0 init
Northbridge init
PCI: 00:02.0 init
PCI: 00:1d.0 init
PCI: 00:1d.1 init
PCI: 00:1d.2 init
PCI: 00:1d.7 init
EHCI: Setting up controller.. done.
PCI: 00:1e.0 init
PCI: 00:1f.0 init
IOAPIC Southbridge enabled 2186
Southbridge APIC ID = 2000000
Set power on if power fails
RTC Init
PNP: 002e.4 init
PNP: 002e.7 init
PCI: 00:1f.1 init
IDE0 IDE1 PCI: 00:1f.3 init
Devices initialized
Copying IRQ routing tables to 0xf0000...done.
Verifing copy of IRQ routing tables at 0xf0000...done
Checking IRQ routing table consistency...
check_pirq_routing_table() - irq_routing_table located at: 0x000f0000
done.
Moving GDT to 0x500...ok
Adjust low_table_end from 0x00000530 to 0x00001000 
Adjust rom_table_end from 0x000f0400 to 0x00100000 
Wrote linuxbios table at: 00000530 - 000006ec  checksum 622a

Welcome to elfboot, the open sourced starter.
January 2002, Eric Biederman.
Version 1.3

rom_stream: 0xfff80000 - 0xfffdffff
Found ELF candidate at offset 0
header_offset is 0
Try to load at offset 0x0
malloc Enter, size 32, free_mem_ptr 00018000
malloc 0x00018000
New segment addr 0x100000 size 0x3d260 offset 0xc0 filesize 0x13248
(cleaned up) New segment addr 0x100000 size 0x3d260 offset 0xc0 filesize 0x13248
lb: [0x0000000000004000, 0x000000000001c000)
malloc Enter, size 32, free_mem_ptr 00018020
malloc 0x00018020
New segment addr 0x13d260 size 0x48 offset 0x13320 filesize 0x48
(cleaned up) New segment addr 0x13d260 size 0x48 offset 0x13320 filesize 0x48
lb: [0x0000000000004000, 0x000000000001c000)
Dropping non PT_LOAD segment
Dropping non PT_LOAD segment
Loading Segment: addr: 0x0000000000100000 memsz: 0x000000000003d260 filesz: 0x0000000000013248
[ 0x0000000000100000, 0000000000113248, 0x000000000013d260) <- 00000000000000c0
Clearing Segment: addr: 0x0000000000113248 memsz: 0x000000000002a018
Loading Segment: addr: 0x000000000013d260 memsz: 0x0000000000000048 filesz: 0x0000000000000048
[ 0x000000000013d260, 000000000013d2a8, 0x000000000013d2a8) <- 0000000000013320
Loaded segments
verified segments
closed down stream
Jumping to boot code at 0x10ea14
entry    = 0x0010ea14
lb_start = 0x00004000
lb_size  = 0x00018000
adjust   = 0x07fe4000
buffer   = 0x07fd0000
     elf_boot_notes = 0x000139a0
adjusted_boot_notes = 0x07ff79a0
FILO version 0.5 (root at smitty2.smittys.pointclark.net) Mon Oct 15 07:40:28 EDT 2007
menu: hdc1:/grub/grub.conf
hdc: LBA 40GB: WDC WD400BB-23FJA0                      
hdd: ATAPI: CD-ROM  Drive/F5D                       
Mounted ext2fs

Press any key to continue.

                                  FILO 0.5

+-------------------------------------------------------------------------+||||||||||||||||||||||||+-------------------------------------------------------------------------+
      Use the ^ and v keys to select which entry is highlighted.
      Press enter to boot the selected OS, 'e' to edit the
      commands before booting, 'a' to modify the kernel arguments
      before booting, or 'c' for a command-line.  Fedora Core (2.6.9-1.667) Console                                        Fedora Core (2.6.9-1.667)                                                Fedora Core 2.6.10-8xx Console-No_Initrd                                 Linux 2.6.10-8xx                                                         Fedora Core (2.6.9-1.667) LB                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                            The highlighted entry will be booted automatically in 20 seconds.    The highlighted entry will be booted automatically in 19 seconds.    The highlighted entry will be booted automatically in 18 seconds.                                                                         Fedora Core (2.6.9-1.667) Console                                        Fedora Core (2.6.9-1.667)                                                Fedora Core (2.6.9-1.667)                                                Fedora Core 2.6.10-8xx Console-No_Initrd                                 Fedora Core 2.6.10-8xx Console-No_Initrd                                 Linux 2.6.10-8xx                                                         Linux 2.6.10-8xx                                                         Fedora Core (2.6.9-1.667) LB                                              Booting 'Fedora Core (2.6.9-1.667) LB'

root (hd2,0)
kernel /vmlinuz-2.6.9-1.667 ro root=/dev/hdc2 console=tty0 console=ttyS0,115200
n8 acpi=off irqpoll lpj=720896
initrd /initrd-2.6.9-1.667.img


Booting 'hdc1:/vmlinuz-2.6.9-1.667 ro root=/dev/hdc2 console=tty0 console=ttyS0
,115200n8 acpi=off irqpoll lpj=720896 initrd=/initrd-2.6.9-1.667.img'
Found Linux version 2.6.9-1.667 (bhcompile at tweety.build.redhat.com) #1 Tue Nov 2 14:41:25 EST 2004 bzImage.
Loading kernel... ok
Loading initrd... ok
Jumping to entry point...
Linux version 2.6.9-1.667 (bhcompile at tweety.build.redhat.com) (gcc version 3.4.2 20041017 (Red Hat 3.4.2-6.fc3)) #1 Tue Nov 2 14:41:25 EST 2004

BIOS-provided physical RAM map:

 BIOS-e820: 0000000000001000 - 00000000000a0000 (usable)

 BIOS-e820: 0000000000100000 - 0000000008000000 (usable)

0MB HIGHMEM available.

128MB LOWMEM available.

zapping low mappings.

DMI not present.

Built 1 zonelists

Kernel command line: ro root=/dev/hdc2 console=tty0 console=ttyS0,115200n8 acpi=off irqpoll lpj=720896

Misrouted IRQ fixup and polling support enabled.

This may significantly impact system performance.

mapped 4G/4G trampoline to ffff4000.

Initializing CPU#0

CPU 0 irqstacks, hard=023d5000 soft=023d4000

PID hash table entries: 1024 (order: 10, 16384 bytes)

Detected 733.260 MHz processor.

Using tsc for high-res timesource

Console: colour dummy device 80x25

Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)

Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)

Memory: 125644k/131072k available (2068k kernel code, 4864k reserved, 647k data, 144k init, 0k highmem)

Calibrating delay loop (skipped)... 1441.79 BogoMIPS preset

Security Scaffold v1.0.0 initialized

SELinux:  Initializing.

SELinux:  Starting in permissive mode

There is already a security framework initialized, register_security failed.

selinux_register_security:  Registering secondary module capability

Capability LSM initialized as secondary

Mount-cache hash table entries: 512 (order: 0, 4096 bytes)

CPU: L1 I cache: 16K, L1 D cache: 16K

CPU: L2 cache: 256K

Intel machine check architecture supported.

Intel machine check reporting enabled on CPU#0.

CPU: Intel Mobile Intel(R) Celeron(TM) CPU          733MHz stepping 04

Enabling fast FPU save and restore... done.

Enabling unmasked SIMD FPU exception support... done.

Checking 'hlt' instruction... 


More information about the coreboot mailing list