Difference between revisions of "VGA support"

From coreboot
Jump to: navigation, search
(Extracting from the system)
 
(40 intermediate revisions by 16 users not shown)
Line 1: Line 1:
= VGA initialization in coreboot v2 =
+
== VGA initialization in coreboot ==
  
== General ==
+
Since coreboot v4 you can configure VGA initialization in Kconfig. For older versions of coreboot check the history of this page.
  
You need to enable two CONFIG options in your Mainboard Option.lb
+
First do:
  
 
<source lang="bash">
 
<source lang="bash">
# VGA Console
+
$ make menuconfig
option CONFIG_CONSOLE_VGA=1
 
option CONFIG_PCI_ROM_RUN=1
 
 
</source>
 
</source>
  
'''CONFIG_PCI_ROM_RUN''' will use the embedded x86 emulator to run the BIOS image in the expansion ROM of a PCI device.
+
Then go
'''CONFIG_CONSOLE_VGA''' will redirect console messages to the VGA screen once VGA card is initialized.
+
    Chipset  --->
 +
      [*] Setup bridges on path to VGA adapter
 +
      [*] Run VGA option ROMs
 +
      Option ROM execution type (Native mode)  --->
  
For add-on (PCI/PCIe/PCI-X/AGP) VGA cards, you don't have to do anything else besides these two CONFIG options.
+
Alternatively you can choose the "Secure mode" to run the VGA option rom in a contained environment.
If your mainboard has an on-board VGA chip and you insert another VGA add-on card, the add-on
 
VGA card will be used instead of the on-board VGA chip.
 
  
== On-board Video Devices ==
+
If you have no on-board graphics, you are done configuring coreboot at this point. You may exit configuration, and run make to get your VGA enabled coreboot image.
  
If you want to use the onboard VGA chip, you have to add the following options in addition to the CONFIG options described above.
+
=== On-board Video Devices ===
  
=== Mainboard Configuration ===
+
If you run coreboot on a system with on-board graphics, you have to embed a VGA  on the top level, enter the file name of your option rom and the PCI ID of the associated graphics device in the form <vendor_id>,<device_id>:
  
1. In the mainboard's Config.lb (./src/mainboard/<mfg>/<board>/Config.lb) You need to specify the device number for your on-board VGA and the address that the video bios will show up at in the system.
+
    VGA BIOS  --->
 +
    [*] Add a VGA BIOS image
 +
    (oprom-0.rom) VGA BIOS path and filename
 +
    (8086,27a2) VGA device PCI IDs
  
<source lang = bash>
+
That's it, exit configuration, and run make to get your VGA enabled coreboot image.
device pci 9.0 on  # PCI
 
        chip drivers/pci/onboard
 
                device pci 9.0 on end
 
                register "rom_address" = "0xfff80000" #512k image
 
                #register "rom_address" = "0xfff00000" #1M image
 
        end
 
end
 
</source>
 
  
Replace the 9.0 with the dev.fn of your vga device.  You can find this number by doing a 'lspci' from the board booted under linux.
+
== How to retrieve a good video bios ==
Please make sure the device number is correct. Otherwise the config code can not compute the proper ROM address.
 
  
 +
There are various ways to get hold of the video bios blob and not all work equally good for all boards (rather the opposite).
  
==== How to compute the "rom_address" value ====
+
The best way is to extract it from the vendor firmware.
 +
In the case of a traditional x86 BIOS this is rather easy and very reliable.
 +
On UEFI systems there does not seem to be a unified way of success but sometimes the steps below work.
  
ROM (called 'flash' a lot) chips are located directly below 4Gbyte  (0xffffffff) boundary.
+
Another category is downloading the blobs directly.
 +
Some vendors offer them in graphics driver packages etc. and you might even find them on enthusiasts website dedicated to firmware modding etc.
  
So you need to calculate the address by subtracting the
+
The most delicate ways are by dumping the blob from a running system.
flash chip size (and adding the offset within the image)
+
This might sound like the most reasonable way but the image present after boot might not be the same as it is (to be) stored in flash (e.g. if it is self modifying).
 +
However, in some cases this is the only way and then it is quite comfortable.
  
In coreboot the offset within the image is 0, because its the first
+
=== RECOMMENDED: Extracting from your vendor bios image ===
thing in the coreboot image.
 
  
So you need to compute the address in the systems memory space where the start of the video bios will show up.
+
The recommended method is to take your mainboard vendor's BIOS image (if there is one) and extract the VGA BIOS using a tool called [[bios_extract]].
  
To do this you take the 4Gb of address and subtract the size of your coreboot image.
+
$ git clone http://review.coreboot.org/p/bios_extract.git
0x100000000 - (ROM size in Kb * 1024)
 
  
You can do this in bash by:
+
This is the most reliable way:
 +
* You are guaranteed to get an image that fits to your onboard VGA
 +
* Even if your VGA BIOS uses self-modifying code you get a correct image
  
<source lang="bash">
+
Decompress your rom image with:
biossize=256
+
$ ./bios_extract hdmag217.rom
printf "0x%x\n" $(( 0x100000000 - ($biossize*1024) ))
 
</source>
 
  
Addresses for popular chip sizes:
+
If bios_decode fails with a message like
  256K 0xfffc0000
+
  Using file "hdmag217.rom" (513kB)
  512k  0xfff80000
+
  Found Phoenix BIOS "Phoenix ServerBIOS 3 Release 6.0    "
  1024k 0xfff00000
+
  Version "DEVEL4E0", created on 03/20/06 at 14:37:39.
 +
  Error: Invalid module signature at 0x80581
  
 +
then you have to cut the flash chip description off the image. In this case the BIOS image is 512KB, so you do
 +
$ dd if=hdmag217.rom of=hdma.rom bs=512k count=1
 +
1+0 records in
 +
1+0 records out
 +
524288 bytes transferred in 0.000883 secs (593688784 bytes/sec)
  
=== Target Configuration ===
 
  
2. You still need to modify your target 'Config.lb' to reserve space for the additional video bios.  Reduce the size of your coreboot image by the size of the video bios. You will prepend the video bios to the coreboot image in step 3.
+
You will get an output similar to this:
  
in the normal section
+
Using file "hdma.rom" (512kB)
 +
Found Phoenix BIOS "Phoenix ServerBIOS 3 Release 6.0    "
 +
Version "DEVEL4E0", created on 03/20/06 at 14:37:39.
 +
0x715FC ( 27134 bytes)  ->  romexec_0.rom
 +
0x6E1CB ( 13338 bytes)  ->  strings_0.rom (29401 bytes)
 +
0x6D65D (  2899 bytes)  ->  display_0.rom (4128 bytes)
 +
0x6B62E (  8208 bytes)  ->  update_0.rom
 +
0x6B1E3 (  1072 bytes)  ->  decompcode_0.rom [0x5000:0xB6D0]
 +
0x6564F ( 23421 bytes)  ->  oprom_0.rom (36864 bytes)
 +
0x65608 (    44 bytes)  ->  tcpa_H_0.rom (32 bytes)
 +
0x65592 (    91 bytes)  ->  acpi_1.rom (116 bytes)
 +
0x65519 (    94 bytes)  ->  acpi_2.rom (244 bytes)
 +
0x654ED (    13 bytes)  ->  tcpa_*_0.rom
 +
0x64D4F (  1927 bytes)  ->  bioscode_0.rom (31382 bytes) [0xF000:0x856A]
 +
0x60020 ( 19728 bytes)  ->  romexec_1.rom
 +
0x570D9 ( 36656 bytes)  ->  oprom_1.rom (61440 bytes)
 +
0x4DB9D ( 38177 bytes)  ->  oprom_2.rom (63488 bytes)
 +
0x46493 ( 30447 bytes)  ->  oprom_3.rom (65536 bytes)
 +
0x41DAB ( 18125 bytes)  ->  logo_0.rom (310162 bytes)
 +
0x39CA5 ( 25439 bytes)  ->  oprom_4.rom (51200 bytes)
 +
0x36005 ( 15493 bytes)  ->  setup_0.rom (37682 bytes)
 +
0x325D7 ( 14867 bytes)  ->  template_0.rom (37728 bytes)
 +
0x2FA36 ( 11142 bytes)  ->  miser_0.rom (16208 bytes)
 +
0x2E63C (  5087 bytes)  ->  tcpa_Q_0.rom (16096 bytes)
 +
0x2D7C3 (  3678 bytes)  ->  acpi_0.rom (10464 bytes)
 +
0x1FA2A ( 41023 bytes)  ->  bioscode_1.rom (56080 bytes) [0xE000:0x40F0]
 +
0x14FE0 ( 43567 bytes)  ->  bioscode_2.rom (62416 bytes) [0x6000:0xCC30]
 +
0x0EB4C ( 25721 bytes)  ->  bioscode_3.rom (36976 bytes) [0x6000:0x3BC0]
 +
0x0D0A0 (  6801 bytes)  ->  bioscode_4.rom (31856 bytes) [0x5000:0xBF50]
  
<source lang="bash">
+
Now you can check the option roms (oprom_?.rom) with the tool romheaders which is part of the [http://www.openfirmware.info/FCODE_suite FCode Suite] (in debian-based distros, you can get it by installing the '''fcode-utils''' package):
romimage "normal"
 
  # 48K for SCSI FW or ATI ROM
 
  option ROM_SIZE = 475136
 
</source>
 
  
or if you only have a "fallback" boot then use the "fallback" section instead.
+
$ romheaders oprom_0.rom
 +
 +
Image 1:
 +
PCI Expansion ROM Header:
 +
  Signature: 0x55aa (Ok)
 +
  CPU unique data: 0x48 0xeb 0x7b 0x01 0x76 0x00 0x00 0x00
 +
                    0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
 +
  Pointer to PCI Data Structure: 0x017c
 +
 +
PCI Data Structure:
 +
  Signature: 0x50434952 'PCIR' (Ok)
 +
  Vendor ID: 0x1002
 +
  Device ID: 0x4752
 +
  Vital Product Data:  0x0000
 +
  PCI Data Structure Length: 0x0018 (24 bytes)
 +
  PCI Data Structure Revision: 0x00
 +
  Class Code: 0x030000 (VGA Display controller)
 +
  Image Length: 0x0048 blocks (36864 bytes)
 +
  Revision Level of Code/Data: 0x0421
 +
  Code Type: 0x00 (Intel x86)
 +
  Last-Image Flag: 0x80 (last image in rom)
 +
  Reserved: 0x0000
 +
 +
Platform specific data for x86 compliant option rom:
 +
  Initialization Size: 0x48 (36864 bytes)
 +
  Entry point for INIT function: 0x80
  
In the above example the bios chip is 512Kb part.  The video bios is  48Kb.  So (512*1024)-(48*1024) = 475136.
+
Congratulations, that's your option rom (compare PCI IDs and Class Code to find it among the option roms).
  
=== Creating an Image ===
+
=== UEFI Method ===
  
3. Finally, prepend your video bios to the coreboot.rom
+
UEFI's format is more structured than that of a traditional flat binary BIOS. In order to extract the VBIOS Option ROM you will need
 +
to parse out the UEFI Volumes and sub-Volumes out the UEFI filesystem using the [https://github.com/LongSoft/UEFITool UEFITool].
  
<source lang="bash">
+
* Look for the " CSMCORE " DXE Driver ? usually having the hash 'a062cf1f-8473-4aa3-8793-600bc4ffe9a8'?
cat <videobios.bin> coreboot.rom > final_coreboot.rom
+
* Search for text "VGA Compatible BIOS" ('''uncheck unicode''')
</source>
+
* Search for text "PCIR" ('''uncheck unicode''')
  
where <videobios.bin> is the name of your video bios image.
+
Double clicking the matching line in the "Messages" section should select the appropriate RAW section. From the menu select "Action -> Section -> Extract Body...".
You need to make sure the final_coreboot.rom size is the size of your ROM chip. Normally 256kb, 512kb, or 1024Kb.
 
  
dd is helpfull to get your <videobios.bin> when booted under the  factory BIOS.
+
=== Downloading ===
  
 +
There are sites that have video BIOS ROMs on their website (with all implications of retrieving a binary from an unknown source and executing it...).
  
= VGA initialization in coreboot v3 =
+
For Intel onboard graphics you can download the vbios (vga bios) from Intel's download section. The vbios is included with some versions of the graphics driver. The summary will say something like "NOTE:These materials are intended for use by developers.Includes VBIOS". The actual vbios file is the *.dat file included with the graphics driver.
  
In coreboot v3 you have to set your PCI option ROM execution method under the '''Device''' menu. The default is x86emu. To get a smaller (and slightly more insecure) version, you can switch to vm86. If you don't want option rom execution, set it to Disabled.
+
=== Retrieval via Linux kernel ===
 +
Some Linux drivers (e.g. <tt>radeon</tt> for AMD) make option ROMs like the video blob available to user space via sysfs.
 +
To use that to get the blob you need to enable it first.
 +
To that end you need to determine the path within <tt>/sys</tt> corresponding to your graphics chip.
 +
It looks like this: <tt>/sys/devices/pci<domain>:<bus>/<domain>:<bus>:<slot>.<function>/rom</tt>.
  
== On-board devices ==
+
You can get the respective information with <tt>lspci</tt>, for example:
 +
# lspci -tv
 +
-[0000:00]-+-00.0  Advanced Micro Devices, Inc. [AMD] Family 16h Processor Root Complex
 +
            +-01.0  Advanced Micro Devices, Inc. [AMD/ATI] Kabini [Radeon HD 8210]
 +
...
  
To add option roms for on-board video cards to your coreboot image, you can just add the image using lar:
+
Here the the needed bits (for the ROM of the Kabini device) are:
 +
* PCI domain: (almost always) 0000
 +
* PCI bus: (also very commonly) 00
 +
* PCI slot: 01 (logical slot; different from any physical slots)
 +
* PCI function: 0 (a PCI device might have multiple functions... shouldn't matter here)
  
<source lang="bash">
+
To enable reading of the ROM you need to write 1 to the respective file, e.g.:
lar -C lzma -a coreboot.rom vgabios.rom:pciXXXX,YYYY.rom
 
</source>
 
  
In the above example, vgabios.rom is the name of your option rom on disk. XXXX is the PCI vendor ID of your on-board video adapter and YYYY is its PCI device ID.
+
echo 1 > /sys/devices/pci0000:00/0000:00:01.0/rom
  
= How to retrieve a good video bios =
+
The same file should then contain the video blob and it should be possible to simply copy it, e.g.:
  
== Extracting from your vendor bios image ==
+
cp /sys/devices/pci0000:00/0000:00:01.0/rom vgabios.bin
  
The recommended method is to take your mainboard vendor's BIOS image and extract the VGA BIOS using a tool called awardeco/amideco/phnxdeco. This is the most reliable way:
+
<tt>romheaders</tt> should print reasonable output for this file.
* You are guaranteed to get an image that fits to your onboard VGA
 
* Even if your VGA BIOS uses self-modifying code you get a correct image
 
  
== Downloading ==
+
Intel Graphics supports this method. See [https://01.org/linuxgraphics/documentation/development/how-dump-video-bios How to dump Video BIOS].
  
There are sites that have video bios roms on their website. (I know of this one for nvidia cards: [http://whitebunny.demon.nl/hardware/chipset_nvidia.html])
+
=== Extraction from mapped memory (if everything else fails) ===
  
== Extracting from the system ==
+
However you might be able to retrieve your on-board video BIOS with Linux as well.
  
However you should be able to retrieve your own video bios as well with linux.
+
* Boot up a machine with a commercial BIOS (not coreboot) with the video card you wish to work under coreboot.
* Boot up a machine with a commercial bios (not coreboot) with the video card you wish to work under coreboot.
+
* You can see where and how much your card's bios is using by doing a  
* You can see where and how much your card's bios is using by<br />doing a <source lang="bash">cat iomem | grep "Video ROM"</source>
+
<source lang="bash">grep 'Video ROM' /proc/iomem</source>
* From the command line enter:<br /><source lang="bash">dd if=/dev/mem of=vgabios.bin bs=1k count=64 skip=768</source> This assumes you card's bios is cached at 0xc0000, and is 64K long. Alternatively you can automatically generate it using this nice script from Peter Stuge:<br />
+
* From the command line enter:<br /><source lang="bash">dd if=/dev/mem of=vgabios.bin bs=1k count=64 skip=768</source> This assumes you card's BIOS is cached at 0xc0000, and is 64K long.
 +
<br /><source lang="bash">dd if=/dev/mem of=video.bios.bin.4 bs=65536 count=1 skip=12</source>
 +
This works for many of the VIA Epia boards.<br>
 +
Alternatively you can automatically generate it using this nice script from Peter Stuge:<br />
 
<source lang="bash">
 
<source lang="bash">
$ grep 'Video ROM' /proc/iomem|(read m; m=${m/ :*}; s=${m/-*}; e=${m/*-}; \
+
cat /proc/iomem | grep 'Video ROM' | (read m; m=${m/ :*}; s=${m/-*}; e=${m/*-}; \
$ dd if=/dev/mem of=vgabios.bin bs=1c skip=$[0x$s] count=$[$[0x$e]-$[0x$s]+1])
+
dd if=/dev/mem of=vgabios.bin bs=1c skip=$[0x$s] count=$[$[0x$e]-$[0x$s]+1])
 
</source>
 
</source>
* You now have a video bios image
+
* You (might) have a video BIOS image now. Check it at least with romheaders (as described above).
 +
 
 +
== YABEL ==
 +
* Yabel can be used to trace the VGA option rom.
 +
* However its ability to prevent the option rom to do nasty things is limited: Often the GPU offers a way (e.g. trough an IO BAR) to access arbitrary locations in RAM, so limiting access of the GPU's PCI device to the option rom wouldn't contain it completely.
 +
 
 +
See [[Coreboot Options]] for more information about the option.
 +
 
 +
[[Category:Blobs]]

Latest revision as of 14:47, 12 April 2016

VGA initialization in coreboot

Since coreboot v4 you can configure VGA initialization in Kconfig. For older versions of coreboot check the history of this page.

First do:

 $ make menuconfig

Then go

    Chipset  --->
     [*] Setup bridges on path to VGA adapter 
     [*] Run VGA option ROMs
     Option ROM execution type (Native mode)  --->

Alternatively you can choose the "Secure mode" to run the VGA option rom in a contained environment.

If you have no on-board graphics, you are done configuring coreboot at this point. You may exit configuration, and run make to get your VGA enabled coreboot image.

On-board Video Devices

If you run coreboot on a system with on-board graphics, you have to embed a VGA on the top level, enter the file name of your option rom and the PCI ID of the associated graphics device in the form <vendor_id>,<device_id>:

   VGA BIOS  --->
    [*] Add a VGA BIOS image
    (oprom-0.rom) VGA BIOS path and filename
    (8086,27a2) VGA device PCI IDs

That's it, exit configuration, and run make to get your VGA enabled coreboot image.

How to retrieve a good video bios

There are various ways to get hold of the video bios blob and not all work equally good for all boards (rather the opposite).

The best way is to extract it from the vendor firmware. In the case of a traditional x86 BIOS this is rather easy and very reliable. On UEFI systems there does not seem to be a unified way of success but sometimes the steps below work.

Another category is downloading the blobs directly. Some vendors offer them in graphics driver packages etc. and you might even find them on enthusiasts website dedicated to firmware modding etc.

The most delicate ways are by dumping the blob from a running system. This might sound like the most reasonable way but the image present after boot might not be the same as it is (to be) stored in flash (e.g. if it is self modifying). However, in some cases this is the only way and then it is quite comfortable.

RECOMMENDED: Extracting from your vendor bios image

The recommended method is to take your mainboard vendor's BIOS image (if there is one) and extract the VGA BIOS using a tool called bios_extract.

$ git clone http://review.coreboot.org/p/bios_extract.git

This is the most reliable way:

  • You are guaranteed to get an image that fits to your onboard VGA
  • Even if your VGA BIOS uses self-modifying code you get a correct image

Decompress your rom image with:

$ ./bios_extract hdmag217.rom

If bios_decode fails with a message like

Using file "hdmag217.rom" (513kB)
Found Phoenix BIOS "Phoenix ServerBIOS 3 Release 6.0     "
Version "DEVEL4E0", created on 03/20/06 at 14:37:39.
Error: Invalid module signature at 0x80581

then you have to cut the flash chip description off the image. In this case the BIOS image is 512KB, so you do

$ dd if=hdmag217.rom of=hdma.rom bs=512k count=1
1+0 records in
1+0 records out
524288 bytes transferred in 0.000883 secs (593688784 bytes/sec)


You will get an output similar to this:

Using file "hdma.rom" (512kB)
Found Phoenix BIOS "Phoenix ServerBIOS 3 Release 6.0     "
Version "DEVEL4E0", created on 03/20/06 at 14:37:39.
0x715FC ( 27134 bytes)   ->   romexec_0.rom
0x6E1CB ( 13338 bytes)   ->   strings_0.rom	(29401 bytes)
0x6D65D (  2899 bytes)   ->   display_0.rom	(4128 bytes)
0x6B62E (  8208 bytes)   ->   update_0.rom
0x6B1E3 (  1072 bytes)   ->   decompcode_0.rom			 [0x5000:0xB6D0]
0x6564F ( 23421 bytes)   ->   oprom_0.rom	(36864 bytes)
0x65608 (    44 bytes)   ->   tcpa_H_0.rom	(32 bytes)
0x65592 (    91 bytes)   ->   acpi_1.rom	(116 bytes)
0x65519 (    94 bytes)   ->   acpi_2.rom	(244 bytes)
0x654ED (    13 bytes)   ->   tcpa_*_0.rom
0x64D4F (  1927 bytes)   ->   bioscode_0.rom	(31382 bytes)	 [0xF000:0x856A]
0x60020 ( 19728 bytes)   ->   romexec_1.rom
0x570D9 ( 36656 bytes)   ->   oprom_1.rom	(61440 bytes)
0x4DB9D ( 38177 bytes)   ->   oprom_2.rom	(63488 bytes)
0x46493 ( 30447 bytes)   ->   oprom_3.rom	(65536 bytes)
0x41DAB ( 18125 bytes)   ->   logo_0.rom	(310162 bytes)
0x39CA5 ( 25439 bytes)   ->   oprom_4.rom	(51200 bytes)
0x36005 ( 15493 bytes)   ->   setup_0.rom	(37682 bytes)
0x325D7 ( 14867 bytes)   ->   template_0.rom	(37728 bytes)
0x2FA36 ( 11142 bytes)   ->   miser_0.rom	(16208 bytes)
0x2E63C (  5087 bytes)   ->   tcpa_Q_0.rom	(16096 bytes)
0x2D7C3 (  3678 bytes)   ->   acpi_0.rom	(10464 bytes)
0x1FA2A ( 41023 bytes)   ->   bioscode_1.rom	(56080 bytes)	 [0xE000:0x40F0]
0x14FE0 ( 43567 bytes)   ->   bioscode_2.rom	(62416 bytes)	 [0x6000:0xCC30]
0x0EB4C ( 25721 bytes)   ->   bioscode_3.rom	(36976 bytes)	 [0x6000:0x3BC0]
0x0D0A0 (  6801 bytes)   ->   bioscode_4.rom	(31856 bytes)	 [0x5000:0xBF50]

Now you can check the option roms (oprom_?.rom) with the tool romheaders which is part of the FCode Suite (in debian-based distros, you can get it by installing the fcode-utils package):

$ romheaders oprom_0.rom 

Image 1:
PCI Expansion ROM Header:
  Signature: 0x55aa (Ok)
  CPU unique data: 0x48 0xeb 0x7b 0x01 0x76 0x00 0x00 0x00
                   0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
  Pointer to PCI Data Structure: 0x017c

PCI Data Structure:
  Signature: 0x50434952 'PCIR' (Ok)
  Vendor ID: 0x1002
  Device ID: 0x4752
  Vital Product Data:  0x0000
  PCI Data Structure Length: 0x0018 (24 bytes)
  PCI Data Structure Revision: 0x00
  Class Code: 0x030000 (VGA Display controller)
  Image Length: 0x0048 blocks (36864 bytes)
  Revision Level of Code/Data: 0x0421
  Code Type: 0x00 (Intel x86)
  Last-Image Flag: 0x80 (last image in rom)
  Reserved: 0x0000

Platform specific data for x86 compliant option rom:
  Initialization Size: 0x48 (36864 bytes)
  Entry point for INIT function: 0x80

Congratulations, that's your option rom (compare PCI IDs and Class Code to find it among the option roms).

UEFI Method

UEFI's format is more structured than that of a traditional flat binary BIOS. In order to extract the VBIOS Option ROM you will need to parse out the UEFI Volumes and sub-Volumes out the UEFI filesystem using the UEFITool.

  • Look for the " CSMCORE " DXE Driver ? usually having the hash 'a062cf1f-8473-4aa3-8793-600bc4ffe9a8'?
  • Search for text "VGA Compatible BIOS" (uncheck unicode)
  • Search for text "PCIR" (uncheck unicode)

Double clicking the matching line in the "Messages" section should select the appropriate RAW section. From the menu select "Action -> Section -> Extract Body...".

Downloading

There are sites that have video BIOS ROMs on their website (with all implications of retrieving a binary from an unknown source and executing it...).

For Intel onboard graphics you can download the vbios (vga bios) from Intel's download section. The vbios is included with some versions of the graphics driver. The summary will say something like "NOTE:These materials are intended for use by developers.Includes VBIOS". The actual vbios file is the *.dat file included with the graphics driver.

Retrieval via Linux kernel

Some Linux drivers (e.g. radeon for AMD) make option ROMs like the video blob available to user space via sysfs. To use that to get the blob you need to enable it first. To that end you need to determine the path within /sys corresponding to your graphics chip. It looks like this: /sys/devices/pci<domain>:<bus>/<domain>:<bus>:<slot>.<function>/rom.

You can get the respective information with lspci, for example:

# lspci -tv
-[0000:00]-+-00.0  Advanced Micro Devices, Inc. [AMD] Family 16h Processor Root Complex
           +-01.0  Advanced Micro Devices, Inc. [AMD/ATI] Kabini [Radeon HD 8210]
...

Here the the needed bits (for the ROM of the Kabini device) are:

  • PCI domain: (almost always) 0000
  • PCI bus: (also very commonly) 00
  • PCI slot: 01 (logical slot; different from any physical slots)
  • PCI function: 0 (a PCI device might have multiple functions... shouldn't matter here)

To enable reading of the ROM you need to write 1 to the respective file, e.g.:

echo 1 > /sys/devices/pci0000:00/0000:00:01.0/rom

The same file should then contain the video blob and it should be possible to simply copy it, e.g.:

cp /sys/devices/pci0000:00/0000:00:01.0/rom vgabios.bin

romheaders should print reasonable output for this file.

Intel Graphics supports this method. See How to dump Video BIOS.

Extraction from mapped memory (if everything else fails)

However you might be able to retrieve your on-board video BIOS with Linux as well.

  • Boot up a machine with a commercial BIOS (not coreboot) with the video card you wish to work under coreboot.
  • You can see where and how much your card's bios is using by doing a
grep 'Video ROM' /proc/iomem
  • From the command line enter:
    dd if=/dev/mem of=vgabios.bin bs=1k count=64 skip=768
    This assumes you card's BIOS is cached at 0xc0000, and is 64K long.

dd if=/dev/mem of=video.bios.bin.4 bs=65536 count=1 skip=12

This works for many of the VIA Epia boards.
Alternatively you can automatically generate it using this nice script from Peter Stuge:

cat /proc/iomem | grep 'Video ROM' | (read m; m=${m/ :*}; s=${m/-*}; e=${m/*-}; \
dd if=/dev/mem of=vgabios.bin bs=1c skip=$[0x$s] count=$[$[0x$e]-$[0x$s]+1])
  • You (might) have a video BIOS image now. Check it at least with romheaders (as described above).

YABEL

  • Yabel can be used to trace the VGA option rom.
  • However its ability to prevent the option rom to do nasty things is limited: Often the GPU offers a way (e.g. trough an IO BAR) to access arbitrary locations in RAM, so limiting access of the GPU's PCI device to the option rom wouldn't contain it completely.

See Coreboot Options for more information about the option.